Officially, “flathead” refers to countersunk screws. Slotted screws are terrible for my purposes, but they actually do have 1 advantage. If they get mud or something caked up in the slot it’s relatively easy to use a knife or some other pointy thing to clean it out. Guns and other things used in dirty environments often use slotted fasteners for that reason.
Right, field maintenance, especially when you don’t have access to tools is a bit of an exception. Personally I think using take down pins for guns is the way to go for field maintenance anyway.
Square (Robertson) and/or torx depending on application. Square should be for everyday things and torx should be for anything mechanical, yes I know there is a big gray area in the middle there, but flat head, phillips, and hex need to go.
The way I see it, anything with a square bit can be done by with a hand held screw driver, and anything with a torx bit should probably be torqued to a certain amount and/or be used with a screw gun. Square/Robertson bits are used super often in things like electrical panels and electronics. They are becoming pretty common for cabinetry also. I doubt you’ll see a torx screw in cabinets.
Thank you for replying. Robertson screws are not common in Scandinavia - at least I’ve never seen one IRL. I use torx for everything, never had an issue with hand screwing them, which is why I asked. But I’m not an expert or professional, just a home owner that tries to DIY as much as I can.
Not having to deal with stripped screws is the biggest plus for me, I hate having to remove a Philips or flathead screw that someone else put in some hard-to-reach location that can’t be turned without breaking. (Which happens surprisingly often, actually.)
I have never in my life seen such a screw. Hexagon is the shit here, when it isnt Phillips. Maybe coming from Ikea, I don’t know. Is this format a (popular) US thing?
Ya Ikea standardized on hex because it’s cheap to mass produce. It definitely strips though.
Torx has slowly been gaining popularity in the US for a decade or two now, but sadly Phillips is still pretty popular and hex is pretty common also, you will see the square/Robertson screws a lot in electrical panels and in cabinetry but not super common at the hardware store.
Torx for anything that needs to be torqued or used with power tools, Robertson (square) for anything intended to be used with hand tools or more finer work (a screwdriver)
I don’t get the problem with flathead, for household applications it seems the most superior because I can use literally anything in my house to drive the screw (butter knife, credit card, a housekey)
plus almost every size of flathead screwdriver can fit in almost every size of flathead screw.
You can use everything, but everything works badly. Even a fitting screwdriver will just randomly jump out after half a turn and scratch whatever you’re working on.
No offense, but you haven’t unscrewed/screwed enough slot screws if you don’t see why they’re worse in every way. The criteria for a good screw isn’t that you don’t have to have the correct tool. The bits are $0.99!
I unscrew a single screw and whether it’s a light switch or an electronic device, I’m already annoyed. Even if you use a flathead screwdriver that fits perfectly, it will un-center and slip out, whether you use a hand bit/screw driver or a drill.
Can we all agree that flathead should be outlawed and Phillips needs to get phased out with a quickness
Why are there so many fasteners 8min : https://youtu.be/5cA9bZRHpZE
Officially, “flathead” refers to countersunk screws. Slotted screws are terrible for my purposes, but they actually do have 1 advantage. If they get mud or something caked up in the slot it’s relatively easy to use a knife or some other pointy thing to clean it out. Guns and other things used in dirty environments often use slotted fasteners for that reason.
Yeah it also really difficult to strip a Flathead slot.
But it can be done! https://media.tenor.com/3dnzk_8PqwoAAAAM/dumb-and-dumber-jim-carrey.gif
Right, field maintenance, especially when you don’t have access to tools is a bit of an exception. Personally I think using take down pins for guns is the way to go for field maintenance anyway.
Wait what should the standard be?
Torx.
Googles it.
Omg, it has 6 sides, that means it’s bestagon
You know! ❤️
I don’t think I had ever actually seen a torx screw head until this conversation lol
If you have an iPhone, you can see two tiny torx screws on the bottom by the lightning/USB-C port
Square (Robertson) and/or torx depending on application. Square should be for everyday things and torx should be for anything mechanical, yes I know there is a big gray area in the middle there, but flat head, phillips, and hex need to go.
Honest question, why not torx across the board? What do square do well that’s not covered by torx?
Robertson is tapered, so you just have to hit the hole somewhat and it’ll guide itself in real easy. Torx is fickle to line up and orientate.
The way I see it, anything with a square bit can be done by with a hand held screw driver, and anything with a torx bit should probably be torqued to a certain amount and/or be used with a screw gun. Square/Robertson bits are used super often in things like electrical panels and electronics. They are becoming pretty common for cabinetry also. I doubt you’ll see a torx screw in cabinets.
Thank you for replying. Robertson screws are not common in Scandinavia - at least I’ve never seen one IRL. I use torx for everything, never had an issue with hand screwing them, which is why I asked. But I’m not an expert or professional, just a home owner that tries to DIY as much as I can.
Not having to deal with stripped screws is the biggest plus for me, I hate having to remove a Philips or flathead screw that someone else put in some hard-to-reach location that can’t be turned without breaking. (Which happens surprisingly often, actually.)
Lol absolutely, stripped screws are the worst
I think it’s slightly more expensive to machine?
Amen, brother!
I’d say cross/slit in tiny, torx in small to big screws.
I have never in my life seen such a screw. Hexagon is the shit here, when it isnt Phillips. Maybe coming from Ikea, I don’t know. Is this format a (popular) US thing?
Ya Ikea standardized on hex because it’s cheap to mass produce. It definitely strips though.
Torx has slowly been gaining popularity in the US for a decade or two now, but sadly Phillips is still pretty popular and hex is pretty common also, you will see the square/Robertson screws a lot in electrical panels and in cabinetry but not super common at the hardware store.
Torx for anything that needs to be torqued or used with power tools, Robertson (square) for anything intended to be used with hand tools or more finer work (a screwdriver)
I don’t get the problem with flathead, for household applications it seems the most superior because I can use literally anything in my house to drive the screw (butter knife, credit card, a housekey)
plus almost every size of flathead screwdriver can fit in almost every size of flathead screw.
You can use everything, but everything works badly. Even a fitting screwdriver will just randomly jump out after half a turn and scratch whatever you’re working on.
No offense, but you haven’t unscrewed/screwed enough slot screws if you don’t see why they’re worse in every way. The criteria for a good screw isn’t that you don’t have to have the correct tool. The bits are $0.99!
I unscrew a single screw and whether it’s a light switch or an electronic device, I’m already annoyed. Even if you use a flathead screwdriver that fits perfectly, it will un-center and slip out, whether you use a hand bit/screw driver or a drill.